INSTALLATION INSTRUCTIONS FOR THE PROFILE
IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING.
THE FLEXIBLE CIRCUIT BOARD MUST BE HANDLED CAREFULLY TO AVOID DAMAGE.
1. Remove guitar strings
2. Remove the control cavity cover plate .
3. Remove the pickup ring from the neck position pickup. Gently pull enough slack in the cable to remove the pickup from the cavity. You should be able to do this without disconnecting the cable at the other end. If you do not have a neck position humbucker, use the bridge position.
4. With the flexible circuit in the position shown in figure 1, install the pickup into the PROFILE ring. IMPORTANT: DO NOT AT ANY TIME CAUSE THE CIRCUIT BOARD TO CREASE OR BEND SHARPLY, DOING SO MAY DAMAGE THE TUNER.
5. Adjust the height of the pickup so that it is flush with the ring.
6. Make sure the underside of the pickup is free of wax residue . Remove the adhesive liner from the back of the circuit board and press it onto the back of the pickup as shown in figure 3. There should be slack in the circuit board ” leg” to allow for pickup height adjustment. This leg should make an “S” shape from the ring to the back of the pickup where the body of the circuit board is mounted ( See Fig. 3 ) . DO NOT ALLOW THE LEG TO FOLD OR CREASE.
7. Feed the cable from the circuit board through the existing wire holes in your guitar. You may need to lift the other pickups from their cavities to continue feeding the cable through the guitar. Carefully pull the cable into the control cavity.
8. Install the PROFILE ring as well as the other pickups that you may have lifted out.
9. Turn the guitar upside down and find a location for the battery holder. This holder can be mounted inside the cavity or on the underside of the cover plate. If there is no room for the holder supplied a common 9 volt battery clip can be used . If there is just no room for a 9 volt battery, You can purchase a lithium battery holder from Optronix or your local dealer.
10. Lightly slit the jacket of the cable with a razor down about 2 ½” , making sure not to cut any of the internal wires. Remove the foil shielding from the cable.
11. Note: The use of soldering flux is necessary when soldering this wire. Strip back the insulation on the individual wires about 1/8″ . Twist together the ends of the red wire from the cable and the red wire from the capacitor supplied and slip a piece of the supplied heat shrink tubing over these wires. Slide the tubing down away from the ends. Solder these two wires to the positive ( RED ) of the battery. Slip the other piece of shrink tubing over the black wire from the cable and solder this wire to the battery negative. Pull the shrink tubing up over the solder joints and heat. Solder the white wire to the guitars hot output prior to the volume control. This can be done at the output lug of the toggle switch or at the input lug of the volume pot. Twist together the ends of the bare wire from the cable and the bare wire from the capacitor and solder to the common or ground of the guitar. This wiring will permit you to tune with the volume turned all the way down. NOTE: IF YOU HAVE ACTIVE ELECTRONICS, YOU CAN NOT USE THE SAME BATTERY SOURCE FOR BOTH SYSTEMS. A SEPARATE SOURCE MUST BE INSTALLED FOR THIS TUNER
1. 기타 줄을 제거합니다.
2. 컨트롤부의 캐비티 커버 플레이트를 제거합니다.
3. 넥 픽업의 픽업 링을 제거합니다. 케이블을 부드럽게 잡아당겨 바디 부의 캐비티에서 픽업을
제거합니다. 케이블의 손상 없이 이 작업을 마쳐야 합니다. 만약 넥 부에 험버커 픽업이
없는 경우 브릿지픽업을 이용합니다.
4. 픽업을 PROFILE 링 안에 설치합니다.
주의사항 : 서킷 보드가 접히는 경우 튜너에 악영향을 끼칠 수 있으므로 잦은 교체는 자제 해
주시기 바랍니다.
5. 픽업의 높이를 링과 같은 높이로 조절합니다.
6. 픽업의 밑부분에 왁스 찌꺼기가 없는지 확인 해 주십시오.
서킷보드 뒷 부분의 끈적거리는 라이너를 제거해 주시고 픽업 뒷 쪽에 장착합니다. 서킷보
드 ‘LEG’이라고 하는 픽업의 높이 조절을 위한 부분 있을 것입니다. 이 LEG이 링에서부터 서킷
보드가 위치한 바디의 픽업 뒤 쪽까지 ‘S’자 모양으로 이어져야 합니다. LEG를 접거나 자국이
남게 하지 마세요.
7. 서킷보드에서 부터 기타의 와이어 구멍가지 케이블을 연결합니다.
케이블 연결을 위해 다른 픽업을 캐비티로 부터 들어 내야 할 수도 있습니다. 캐이블을 컨트롤
캐비티까지 조심하여 당겨줍니다.
8. 들어 올렸던 다른 픽업과 함께 PROFILE 링을 설치합니다.
9. 배터리 홀더 장착을 위하여 기타를 살펴봅니다.
이 홀더는 캐비티 안쪽이나 커버 플레이트 안 쪽에 설치할 수 있습니다.
만약 함께 제공된 홀더를 장착할 만한 곳이 적당치 않다면 일반적인 9볼트 배터리 클립을 사용
할 수 있습니다. 만약 9볼트 배터리를 장착할 만한 곳이 적당치 않다면 리튬배터리 홀더를
별도 구매하여 사용하시면 됩니다.
10. 내부 전선에 손상이 가지 않게끔 주의 하면서 케이블 커버를 커터칼이나 면도칼 등을 이용
하여 6.35cm만큼 얇게 갈라줍니다. 케이블을 감싸고 있는 호일을 제공합니다.
배송
평균 배송 기간: 약 2~3일 소요 예상
기본배송료는 3,000원 입니다. (도서,산간,오지 일부지역은 배송비가 추가될 수 있습니다) 50,000원 이상 구매시 무료배송입니다.
교환/반품 정보
상품 청약철회 가능기간은 상품 수령일로 부터 7일 이내 입니다.
상품 택(tag)제거 또는 개봉으로 상품 가치 훼손 시에는 7일 이내라도 교환 및 반품이 불가능합니다.
저단가 상품, 일부 특가 상품은 고객 변심에 의한 교환, 반품은 고객께서 배송비를 부담하셔야 합니다(제품의 하자,배송오류는 제외)
일부 상품은 신모델 출시, 부품가격 변동 등 제조사 사정으로 가격이 변동될 수 있습니다.
신발의 경우, 실외에서 착화하였거나 사용흔적이 있는 경우에는 교환/반품 기간내라도 교환 및 반품이 불가능 합니다.
수제화 중 개별 주문제작상품(굽높이,발볼,사이즈 변경)의 경우에는 제작완료, 인수 후에는 교환/반품기간내라도 교환 및 반품이 불가능 합니다.
수입,명품 제품의 경우, 제품 및 본 상품의 박스 훼손, 분실 등으로 인한 상품 가치 훼손 시 교환 및 반품이 불가능 하오니, 양해 바랍니다.
일부 특가 상품의 경우, 인수 후에는 제품 하자나 오배송의 경우를 제외한 고객님의 단순변심에 의한 교환, 반품이 불가능할 수 있사오니, 각 상품의 상품상세정보를 꼭 참조하십시오.
환불/반품 정책
형제악기사은 소비자의보호를 위해서 규정한 제반 법규를 준수합니다.
주문 취소는 미결재인 상태에서는 고객님이 직접 취소하실 수가 있습니다. 결재후 취소는 저희 고객센타(02-745-8744)로 문의해 주시기 바랍니다.
무통장 입금의 경우 일정기간동안 송금을 하지 않으면 자동 주문 취소가 되고, 구매자가 원하는 경우 인터넷에서 바로 취소 하실 수도 있으며, 송금을 하신 경우에는 환불조치 해드립니다.
카드로 결제하신 경우, 승인 취소가 가능하면 취소을 해드리지만 승인 취소가 불가능한 경우 해당 금액을 모두 송금해 드립니다.
반송을 하실 때에는 주문번호, 회원번호를 메모하여 보내주시면 보다 신속한 처리에 도움이 됩니다.(문의전화 02-745-8744)
우송된 상품이 원하는 상품이 아닌 경우는 우송 받으신 날부터 20일 이내에 아래 주소로 주문번호, 회원번호, 이름, 반품사유 등을 메모하여 반송해 주시면 상품 대금은 회원번호로 예치하여 차후 다른 상품 주문시 사용하실 수 있습니다. (반송료는 고객 부담 입니다.)
반송주소 : 서울 종로구 삼일대로 428 (낙원상가) 형제악기사